Mini water softener

 

What Is UV Water Purifier Part - 1

What is a UV Water Purifier and How Does It Work

A UV water purifier treats micro-biologically unsafe water with germicidal ultraviolet light. The UV wavelength scrambles the DNA of living organisms in the water, so they can no longer reproduce and make you sick. If you drink bacteria-infested water, the organisms can embed in your digestive tract and replicate. Ultraviolet radiation renders bacteria, viruses, parasites, and fungi unable to replicate by damaging the nucleic acids of their DNA.

How a UV water purifier works

A UV water purifier exposes living organisms, such as bacteria, viruses, or cysts (like Cryptosporidium and Giardia) to a germicidal ultraviolet wavelength. With enough energy, UV radiation at the 254-nm wavelength disrupts the DNA in pathogenic microorganisms so they cannot reproduce. The ultraviolet light prevents bacteria from spreading disease through drinking water.

UV dosage is the measurement of energy (in mJ/cm²) delivered by a UV water purifier. The more dosage provided, the more energy delivered to treat contaminated water. At a certain threshold, this energy becomes sufficient enough to inactivate most of the microorganisms present in water.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We Sincere thanks to Fresh water Systems.

What Is reverse Osmosis part - 12

 

Summary

Reverse Osmosis is an effective and proven technology to produce water that is suitable for many industrial applications that require demineralized or deionized water. Further post treatment after the RO system such as mixed bed deionization can increase the quality of the RO permeate and make it suitable for the most demanding applications. Proper pretreatment and monitoring of an RO system is crucial to preventing costly repairs and unscheduled maintenance. With the correct system design, maintenance program, and experienced service support, your RO system should provide many years of high purity water.

What Is Reverse Osmosis Summary Ends Here.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We Sincere thanks to Pure Tech

what Is Reverse Osmosis Part - 11

 

RO Membrane Cleaning

RO membranes will inevitably require periodic cleaning, anywhere from 1 to 4 times a year depending on the feed water quality. As a general rule, if the normalized pressure drop or the normalized salt passage has increased by 15%, then it is time to clean the RO membranes. If the normalized permeate flow has decreased by 15% then it is also time to clean the RO membranes. You can either clean the RO membranes in place or have them removed from the RO system and cleaned off site by a service company that specializes in this service. It has been proven that offsite membrane cleaning is more effective at providing a better cleaning than onsite cleaning skids.

RO membrane cleaning involves low and high pH cleaners to remove contaminants from the membrane. Scaling is addressed with low pH cleaners and organics, colloidal and biofouling are treated with a high pH cleaner. Cleaning RO membranes is not only about using the appropriate chemicals. There are many other factors involved such as flows, water temperature and quality, properly designed and sized cleaning skids and many other factors that an experienced service group must address in order to properly clean RO membranes.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse osmosis part - 10

 

RO Data Trending and Normalization

The RO membranes are the heart of the RO system and certain data points need to be collected to determine the health of the RO membranes. These data points include the system pressures, flows, quality and temperature. Water temperature is directly proportional to pressure. As the water temperature decreases it becomes more viscous and the RO permeate flow will drop as it requires more pressure to push the water through the membrane. Likewise, when the water temperature increases the RO permeate flow will increase. As a result, performance data for an RO system must be normalized so that flow variations are not interpreted as abnormal when no problem exists. The normalized flows, pressures and salt rejection should be calculated, graphed and compared to the baseline data (when the RO was commissioned or after the membranes were cleaned or replaced) to help troubleshoot any problems and also determine when to clean or inspect the membranes for damage. Data normalization helps display the true performance of the RO membranes. As a general rule of thumb, when the normalized change is +/- 15% from the baseline data then you need to take action. If you don't follow this rule then RO membrane cleanings may not be very effective at brining the membranes back to near new performance.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse Osmosis part - 9

 

PRE TREATMENT SOLUTIONS

Below are some pretreatment solutions for RO systems that can help minimize fouling, scaling and chemical attack.

MULTI MEDIA FILTRATION (MMF)

A Multi-Media Filter is used to help prevent fouling of an RO system. A Multi-Media Filter typically contains three layers of media consisting of anthracite coal, sand and garnet, with a supporting layer of gravel at the bottom. These are the medias of choice because of the differences in size and density. The larger (but lighter) anthracite coal will be on top and the heavier (but smaller) garnet will remain on the bottom. The filter media arrangement allows the largest dirt particles to be removed near the top of the media bed with the smaller dirt particles being retained deeper and deeper in the media. This allows the entire bed to act as a filter allowing much longer filter run times between backwash and more efficient particulate removal.

A well-operated Multi-Media Filter can remove particulates down to 15-20 microns. A Multi-Media Filter that uses a coagulant addition (which induces tiny particles to join together to form particles large enough to be filtered) can remove particulates down to 5-10 microns. To put this in perspective, the width of a human hair is around 50 microns.

A multi media filter is suggested when the Silt Density Index (SDI) value is greater than 3 or when the turbidity is greater than 0.2 NTU. There is no exact rule, but the above guidelines should be followed to prevent premature fouling of RO membranes.

It is important to have a 5 micron cartridge filter placed directly after the MMF unit in the event that the under drains of the MMF fail. This will prevent the MMF media from damaging downstream pumps and fouling the RO system.

MICROFILTRATION (MF)

Microfiltration (MF) is effective in removing colloidal and bacteria matter and has a pore size of only 0.1-10µm. Microfiltration is helpful in reducing the fouling potential for an RO unit. Membrane configuration can vary between manufacturers, but the "hollow fiber" type is the most commonly used. Typically, the water is pumped from the outside of the fibers, and the clean water is collected from the inside of the fibers. Microfiltration membranes used in potable water applications usually operate in "dead-end" flow. In dead-end flow, all of the water fed to the membrane is filtered through the membrane. A filter cake that must be periodically backwashed from the membrane surface forms. Recovery rates are normally greater than 90 percent on feed water sources which have fairly high quality and low turbidity feeds.

ANTISCALANTS AND SCALE INHIBITORS

Antiscalants and scale inhibitors, as their name suggests, are chemicals that can be added to feed water before an RO unit to help reduce the scaling potential of the feed water. Antiscalants and scale inhibitors increase the solubility limits of troublesome inorganic compounds. By increasing the solubility limits, you are able to concentrate the salts further than otherwise would be possible and therefore achieve a higher recovery rate and run at a higher concentration factor. Antiscalants and scale inhibitors work by interfering with scale formation and crystal growth. The choice of antiscalant or scale inhibitor to use and the correct dosage depends on the feed water chemistry and RO system design.

SOFTENING BY ION EXCHANGE

A water softener can be used to help prevent scaling in an RO system by exchanging scale forming ions with non scale forming ions. As with a MMF unit, it is important to have a 5 micron cartridge filter placed directly after the water softener in the event that the under drains of the softener fail.

SODIUM BISULFITE (SBS) INJECTION

By adding sodium bisulfite (SBS or SMBS), which is a reducer, to the water stream before an RO at the proper dose you can remove residual chlorine.

GRANULAR ACTIVATED CARBON (GAC)

GAC is used for both removing organic constituents and residual disinfectants (such as chlorine and chloramines) from water. GAC media is made from coal, nutshells or wood. Activated carbon removes residual chlorine and chloramines by a chemical reaction that involves a transfer of electrons from the surface of the GAC to the residual chlorine or chloramines. The chlorine or chloramines ends up as a chloride ion that is no longer an oxidizer.

The disadvantage of using a GAC before the RO unit is that the GAC will remove chlorine quickly at the very top of the GAC bed. This will leave the remainder of the GAC bed without any biocide to kill microorganisms. A GAC bed will absorb organics throughout the bed, which is potential food for bacteria, so eventually a GAC bed can become a breeding ground for bacteria growth which can pass easily to the RO membranes. Likewise, a GAC bed can produce very small carbon fines under some circumstances that have the potential to foul an RO.

 Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse osmosis Part - 8

 

RO Pretreatment

Proper pretreatment using both mechanical and chemical treatments is critical for an RO system to prevent fouling, scaling and costly premature RO membrane failure and frequent cleaning requirements. Below is a summary of common problems an RO system experiences due to lack of proper pretreatment.

FOULING

Fouling occurs when contaminants accumulate on the membrane surface effectively plugging the membrane. There are many contaminants in municipal feed water that are naked to the human eye and harmless for human consumption, but large enough to quickly foul (or plug) an RO system. Fouling typically occurs in the front end of an RO system and results in a higher pressure drop across the RO system and a lower permeate flow. This translates into higher operating costs and eventually the need to clean or replace the RO membranes. Fouling will take place eventually to some extent given the extremely fine pore size of an RO membrane no matter how effective your pretreatment and cleaning schedule is. However, by having proper pretreatment in place, you will minimize the need to address fouling related problems on a regular basis.

Fouling can be caused by the following: 

Particulate or colloidal mater (dirt, silt, clay, etc.)

Organics (humic/fulvic acids, etc)

Microorganisms (bacteria, etc). Bacteria present one of the most common fouling problems since RO membranes in use today cannot tolerate a disinfectant such as chlorine and thefore microorganisms are often able to thrive and multiply on the membrane surface. They may product biofilms that cover the membrane surface and result in heavy fouling.

Breakthrough of filter media upstream of the RO unit. GAC carbon beds and softener beds may develop an under drain leak and if there is not adequate post filtration in place the media can foul the RO system.

By performing analytical tests, you can determine if the feed water to your RO has a high potential for fouling. To prevent fouling of an RO system, mechanical filtration methods are used. The most popular methods to prevent fouling are the use of multi-media filters (MMF) or microfiltration (MF). In some cases cartridge filtration will suffice.

 

SCALING

As certain dissolved (inorganic) compounds become more concentrated (remember discussion on concentration factor) then scaling can occur if these compounds exceed their solubility limits and precipitate on the membrane surface as scale. The results of scaling are a higher pressure drop across the system, higher salt passage (less salt rejection), low permeate flow and lower permeate water quality. An example of a common scale that tends to form on an RO membrane is calcium carbonate (CaCO3).

 

CHEMICAL ATTACK

Modern thin film composite membranes are not tolerant to chlorine or chloramines. Oxidizers such as chlorine will 'burn' holes in the membrane pores and can cause irreparable damage. The result of chemical attack on an RO membrane is a higher permeate flow and a higher salt passage (poorer quality permeate water). This is why microorganism growth on RO membranes tends to foul RO membranes so easily since there is no biocide to prevent its growth.

 

MECHANICAL DAMAGE

Part of the pretreatment scheme should be pre and post RO system plumbing and controls. If 'hard starts' occur mechanical damage to the membranes can occur. Likewise, if there is too much backpressure on the RO system then mechanical damage to the RO membranes can also occur. These can be addressed by using variable frequency drive motors to start high pressure pumps for RO systems and by installing check valve(s) and/or pressure relief valves to prevent excessive back pressure on the RO unit that can cause permanent membrane damage.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse Osmosis Part - 7

 

SINGLE PASS RO VS DOUBLE PASS RO

Think of a pass as a stand alone RO system. With this in mind, the difference between a single pass RO system and a double pass RO system is that with a double pass RO, the permeate from the first pass becomes the feed water to the second pass (or second RO) which ends up producing a much higher quality permeate because it has essentially gone through two RO systems.

 

Besides producing a much higher quality permeate, a double pass system also allows the opportunity to remove carbon dioxide gas from the permeate by injecting caustic between the first and second pass. C02 is undesirable when you have mixed bed ion exchange resin beds after the RO. By adding caustic after the first pass, you increase the pH of the first pass permeate water and convert C02 to bicarbonate (HCO3-) and carbonate (CO3-2) for better rejection by the RO membranes in the second pass. This can't be done with a single pass RO because injecting caustic and forming carbonate (CO3-2) in the presence of cations such as calcium will cause scaling of the RO membranes.

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse Osmosis Part - 6

 

RO SYSTEM WITH CONCENTRATE RECYCLE

With an RO system that can't be properly staged and the feed water chemistry allows for it, a concentrate recycle setup can be utilized where a portion of the concentrate stream is fed back to the feed water to the first stage to help increase the system recovery.

Ro Concentrate Recycle

Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech

What Is Reverse Osmosis Part - 5

 

Reverse Osmosis Performance & Design Calculations

There are a handful of calculations that are used to judge the performance of an RO system and also for design considerations. An RO system has instrumentation that displays quality, flow, pressure and sometimes other data like temperature or hours of operation. In order to accurately measure the performance of an RO system you need the following operation parameters at a minimum:

·         Feed pressure

·         Permeate pressure

·         Concentrate pressure

·         Feed conductivity

·         Permeate conductivity

·         Feed flow

·         Permeate flow

·         Temperature

SALT REJECTION %

This equation tells you how effective the RO membranes are removing contaminants. It does not tell you how each individual membrane is performing, but rather how the system overall on average is performing. A well-designed RO system with properly functioning RO membranes will reject 95% to 99% of most feed water contaminants (that are of a certain size and charge). You can determine how effective the RO membranes are removing contaminants by using the following equation: 

Salt Rejection % =	Conductivity of Feed Water – Conductivity of Permeate Water	× 100
	Conductivity of Feed

The higher the salt rejection, the better the system is performing. A low salt rejection can mean that the membranes require cleaning or replacement.

SALT PASSAGE %

This is simply the inverse of salt rejection described in the previous equation. This is the amount of salts expressed as a percentage that are passing through the RO system. The lower the salt passage, the better the system is performing. A high salt passage can mean that the membranes require cleaning or replacement. 

Salt Passage % = (1 – Salt Rejection %)

RECOVERY %

Percent Recovery is the amount of water that is being 'recovered' as good permeate water. Another way to think of Percent Recovery is the amount of water that is not sent to drain as concentrate, but rather collected as permeate or product water. The higher the recovery % means that you are sending less water to drain as concentrate and saving more permeate water. However, if the recovery % is too high for the RO design then it can lead to larger problems due to scaling and fouling. The % Recovery for an RO system is established with the help of design software taking into consideration numerous factors such as feed water chemistry and RO pre-treatment before the RO system. Therefore, the proper % Recovery at which an RO should operate at depends on what it was designed for. By calculating the % Recovery you can quickly determine if the system is operating outside of the intended design. The calculation for % Recovery is below: 

% Recovery =	Permeate Flow Rate (gpm)	× 100
	Feed Flow Rate (gpm)

For example, if the recovery rate is 75% then this means that for every 100 gallons of feed water that enter the RO system, you are recovering 75 gallons as usable permeate water and 25 gallons are going to drain as concentrate. Industrial RO systems typically run anywhere from 50% to 85% recovery depending the feed water characteristics and other design considerations.

CONCENTRATION FACTOR

The concentration factor is related to the RO system recovery and is an important equation for RO system design. The more water you recover as permeate (the higher the % recovery), the more concentrated salts and contaminants you collect in the concentrate stream. This can lead to higher potential for scaling on the surface of the RO membrane when the concentration factor is too high for the system design and feed water composition.

Concentration Factor =	1
	1 – Recovery %

The concept is no different than that of a boiler or cooling tower. They both have purified water exiting the system (steam) and end up leaving a concentrated solution behind. As the degree of concentration increases, the solubility limits may be exceeded and precipitate on the surface of the equipment as scale. 

For example, if your feed flow is 100 gpm and your permeate flow is 75 gpm, then the recovery is (75/100) x 100 = 75%. To find the concentration factor, the formula would be 1 ÷ (1-75%) = 4. 

A concentration factor of 4 means that the water going to the concentrate stream will be 4 times more concentrated than the feed water is. If the feed water in this example was 500 ppm, then the concentrate stream would be 500 x 4 = 2,000 ppm.

FLUX

Gfd =	gpm of permeate × 1,440 min/day
	# of RO elements in system × square footage of each RO element

For example, you have the following:

The RO system is producing 75 gallons per minute (gpm) of permeate. You have 3 RO vessels and each vessel holds 6 RO membranes. Therefore you have a total of 3 x 6 = 18 membranes. The type of membrane you have in the RO system is a Dow Filmtec BW30-365. This type of RO membrane (or element) has 365 square feet of surface area. 

To find the flux (Gfd): 

Gfd =	75 gpm × 1,440 min/day	=	108,000
	18 elements × 365 sq ft		6,570

The flux is 16 Gfd. 

This means that 16 gallons of water is passed through each square foot of each RO membrane per day. This number could be good or bad depending on the type of feed water chemistry and system design. Below is a general rule of thumb for flux ranges for different source waters and can be better determined with the help of RO design software. If you had used Dow Filmtec LE-440i RO membranes in the above example, then the flux would have been 14. So it is important to factor in what type of membrane is used and to try and keep the type of membrane consistent throughout the system.

Feed Water Source	Gfd
Sewage Effluent	5-10
Sea Water	8-12
Brackish Surface Water	10-14
Brackish Well Water	14-18
RO Permeate Water	20-30

 

MASS BALANCE

A Mass Balance equation is used to help determine if your flow and quality instrumentation is reading properly or requires calibration. If your instrumentation is not reading correctly, then the performance data trending that you are collecting is useless. You will need to collect the following data from an RO system to perform a Mass Balance calculation:

1.      Feed Flow (gpm)

2.      Permeate Flow (gpm)

3.      Concentrate Flow (gpm)

4.      Feed Conductivity (µS)

5.      Permeate Conductivity (µS)

6.      Concentrate Conductivity (µS)

 

The mass balance equation is:

(Feed flow¹ x Feed Conductivity) = (Permeate Flow x Permeate Conductivity)
+ (Concentrate Flow x Concentrate Conductivity)

¹Feed Flow equals Permeate Flow + Concentrate Flow

For example, if you collected the following data from an RO system:

Permeate Flow	5 gpm
Feed Conductivity	500 µS
Permeate Conductivity	10 µS
Concentrate Flow	2 gpm
Concentrate Conductivity	1200 µS

Then the Mass Balance Equation would be:

(7 x 500) = (5 x 10) + (2 x 1200)

3,500 ≠ 2,450

Then find the difference

(Difference / Sum) x 100

((3,500 - 2,450) / (3,500 + 2,450)) x 100

= 18%

A difference of +/- 5% is ok. A difference of +/- 5% to 10% is generally adequate. A difference of > +/- 10% is unacceptable and calibration of the RO instrumentation is required to ensure that you are collecting useful data. In the example above, the RO mass balance equation falls out of range and requires attention.

 Yazh Pure Life

RO Water Purifier Sales and Service.

9786569973

8098094111

We thanks to Pure Tech